Lantronix XPress-DR-IAP Guía de usuario descargar pdf (Pagina 28)

Introduction

1.11 Dimensions

The DSTni-XPress DR dimensions are shown in the following drawing.

95MM

(3.7 in)

35MM

(1.4 in)

60MM

(2.4 in)

RESET

10/100BASE-T

SERIAL

RS232

RS485

1.12 Product Information Label

The product information label contains important information about your specific unit. Your

unit will have one similar to the one below.

Serial Number

S/N:2D00054

DSTni-XPress DR

00-20-4A-2D-00-36

Made in USA

Part Number

MAC ID

Rev. A11

Revision

Note: Before mounting the device on a DIN rail, copy the information from the label.

1-14 DSTni-XPress DR User Guide

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 148 149

DSTni-XPress DR 1
User Guide 1
Copyright and Trademark 3
Disclaimer and Revisions 4
Declaration of Conformity 5
Warranty 6
Sales Offices 7
Contents 10
List of Figures 12
List of Tables 13
1.1 DSTni-XPress DR 15
Introduction 16
PLC's XPress DR-IAP 17
1.4 Serial Interface 19
1.5 RJ-45 Serial Connector 20
1.7 RJ-45 Ethernet Interface 22
1.9 Front Panel Description 25
1.10 LEDs 27
1.11 Dimensions 28
1.13 Power Requirements 29
1.14 Reset Switch 29
1.15 RS-232/RS-485 Switch 30
Table 7 - Technical Specs 31
Getting Started 33
2.1.3 Port Number 34
2.3.1 DHCP 37
2.3.2 AutoIP 37
2.4 DeviceInstaller 38
2.4.3 Test the IP Address 40
2.5 ARP and Telnet 44
2.6 Serial Port Login 45
Configure 47
3.2 Using DeviceInstaller 48
3.3 Web Manager Page 50
3.3.1 Unit Configuration 51
3.3.2 Server Properties 52
3.3.3 Port Properties 53
3.3.4 Update Settings 55
3.3.5 Technical Support 55
3.4.2 Using the Serial Port 58
3.5.1 IP Address 58
3.5.5 DHCP Naming 60
3.6.1 Baudrate 61
3.6.2 I/F (Interface) Mode 61
3.6.3 Flow 62
3.6.4 Port Number 63
3.6.5 Connect Mode 64
3.6.6 Remote IP Address 67
3.6.7 Remote Port 67
3.6.8 DisConnMode 67
3.6.10 Pack Control 69
3.6.12 Send Characters 70
3.6.13 Telnet Terminal Type 70
3.7 Expert Settings 71
3.8 Security Settings 71
3.9 Factory Defaults 73
3.11 Get Configuration 73
3.12 Set Configuration 74
4.1 Protocol Firmware 75
4.2.1 Via DeviceInstaller 76
Firmware 77
4.2.2 Via TFTP 79
4.2.3 Via Another Unit 79
4.2.4 Via the Serial Port 80
5.1 Overview 81
Comm Port Redirector 82
5.3 Using Redirector 83
5.3.1 Port Setup 84
5.3.2 Comm App Setup 84
5.3.5 Port Settings 86
5.3.6 Listen Mode 86
5.3.7 Silent Mode 87
5.3.8 TCP Keepalive 87
6.1 Technical Support 89
Troubleshooting 90
7.1 Monitor Mode 95
0> OK; no error 96
8> Wrong parameter(s) 96
9> Invalid command 96
8.1 UDP Datagrams 97
8.2.2 Sending a Setup Record 100
8.2.3 The Intel Hex Format 101
0300300002337A1E 102
8.3 Setup Records 103
8.3.1 Channel Parameters 104
8.3.2 Interface Mode 105
8.3.3 Baud Rate 106
8.3.4 Flow Control 106
8.3.5 Connect Mode 107
8.3.6 Disconnect Mode 108
8.3.8 Pack Control 109
8.4 IP Addresses 110
8.4.3 Host Portion 111
8.4.4 Network Address 111
8.4.5 Broadcast Address 111
8.4.7 Network RFCs 112
9.1 Connect Mode Options 114
Binary to Hex 115
9.2 Disconnect Mode Options 117
9.4 Interface Mode Options 126
9.5 Pack Control Options 127
10.1 Class A Network 129
10.2 Class B Network 129
10.3 Class C Network 129
10.4 Network Address 130
10.5 Broadcast Address 130
10.6 IP Netmask 130
10.8 Network RFCs 131

Comentarios a estos manuales

Sin comentarios

Lantronix XPress-DR-IAP Guía de usuario Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Servidores De Serie Lantronix XPress-DR-IAP