Lantronix XPress-DR-IAP Guía de usuario Pagina 111
- Pagina / 149
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
UDP
A router is required between all networks and all sub-networks. Generally, hosts can send
packets directly only to hosts on their own sub-network. All packets destined for other
subnets are sent to a router on the local network.
8.4.3 Host Portion
The host portion of the IP address is a unique number assigned to identify the host.
8.4.4 Network Address
A host address with all host bits set to 0 addresses the network as a whole (for example, in
routing entries).
192.168.0.0
8.4.5 Broadcast Address
A host address with all host bits set to 1 is the broadcast address, meaning for “for every
station.”
192.168.0.255
Network and broadcast addresses must not be used as a host address; for example,
192.168.0.0 identifies the entire network, and 192.168.0.255 identifies the broadcast address.
IP Subnet Mask
An IP subnet mask divides IP address differently than the standards defined by the classes A,
B, and C. An IP subnet mask defines the number of bits to be taken from the IP address as the
network or host sections. The Device Server prompts for the number of host bits to be entered
and then calculates the netmask, which is displayed in standard decimal-dot notation (for
example, 255.255.255.0) when saved parameters are displayed.
Table 37 - Standard IP Network Netmasks
Network
Class
Network Bits Host Bits Netmask
A 8 24 255.0.0.0
B 16 16 255.255.0.0
C 24 8 255.255.255.
0
DSTni-XPress DR User Guide 8-15
- DSTni-XPress DR 1
- User Guide 1
- Copyright and Trademark 3
- Disclaimer and Revisions 4
- Declaration of Conformity 5
- Warranty 6
- Sales Offices 7
- Contents 10
- List of Figures 12
- List of Tables 13
- 1.1 DSTni-XPress DR 15
- Introduction 16
- PLC's XPress DR-IAP 17
- 1.4 Serial Interface 19
- 1.5 RJ-45 Serial Connector 20
- 1.7 RJ-45 Ethernet Interface 22
- 1.9 Front Panel Description 25
- 1.10 LEDs 27
- 1.11 Dimensions 28
- 1.13 Power Requirements 29
- 1.14 Reset Switch 29
- 1.15 RS-232/RS-485 Switch 30
- Table 7 - Technical Specs 31
- Getting Started 33
- 2.1.3 Port Number 34
- 2.3.1 DHCP 37
- 2.3.2 AutoIP 37
- 2.4 DeviceInstaller 38
- 2.4.3 Test the IP Address 40
- 2.5 ARP and Telnet 44
- 2.6 Serial Port Login 45
- Configure 47
- 3.2 Using DeviceInstaller 48
- 3.3 Web Manager Page 50
- 3.3.1 Unit Configuration 51
- 3.3.2 Server Properties 52
- 3.3.3 Port Properties 53
- 3.3.4 Update Settings 55
- 3.3.5 Technical Support 55
- 3.4.2 Using the Serial Port 58
- 3.5.1 IP Address 58
- 3.5.5 DHCP Naming 60
- 3.6.1 Baudrate 61
- 3.6.2 I/F (Interface) Mode 61
- 3.6.3 Flow 62
- 3.6.4 Port Number 63
- 3.6.5 Connect Mode 64
- 3.6.6 Remote IP Address 67
- 3.6.7 Remote Port 67
- 3.6.8 DisConnMode 67
- 3.6.10 Pack Control 69
- 3.6.12 Send Characters 70
- 3.6.13 Telnet Terminal Type 70
- 3.7 Expert Settings 71
- 3.8 Security Settings 71
- 3.9 Factory Defaults 73
- 3.11 Get Configuration 73
- 3.12 Set Configuration 74
- 4.1 Protocol Firmware 75
- 4.2.1 Via DeviceInstaller 76
- Firmware 77
- 4.2.2 Via TFTP 79
- 4.2.3 Via Another Unit 79
- 4.2.4 Via the Serial Port 80
- 5.1 Overview 81
- Comm Port Redirector 82
- 5.3 Using Redirector 83
- 5.3.1 Port Setup 84
- 5.3.2 Comm App Setup 84
- 5.3.5 Port Settings 86
- 5.3.6 Listen Mode 86
- 5.3.7 Silent Mode 87
- 5.3.8 TCP Keepalive 87
- 6.1 Technical Support 89
- Troubleshooting 90
- 7.1 Monitor Mode 95
- 0> OK; no error 96
- 8> Wrong parameter(s) 96
- 9> Invalid command 96
- 8.1 UDP Datagrams 97
- 8.2.2 Sending a Setup Record 100
- 8.2.3 The Intel Hex Format 101
- 0300300002337A1E 102
- 8.3 Setup Records 103
- 8.3.1 Channel Parameters 104
- 8.3.2 Interface Mode 105
- 8.3.3 Baud Rate 106
- 8.3.4 Flow Control 106
- 8.3.5 Connect Mode 107
- 8.3.6 Disconnect Mode 108
- 8.3.8 Pack Control 109
- 8.4 IP Addresses 110
- 8.4.3 Host Portion 111
- 8.4.4 Network Address 111
- 8.4.5 Broadcast Address 111
- 8.4.7 Network RFCs 112
- 9.1 Connect Mode Options 114
- Binary to Hex 115
- 9.2 Disconnect Mode Options 117
- 9.4 Interface Mode Options 126
- 9.5 Pack Control Options 127
- 10.1 Class A Network 129
- 10.2 Class B Network 129
- 10.3 Class C Network 129
- 10.4 Network Address 130
- 10.5 Broadcast Address 130
- 10.6 IP Netmask 130
- 10.8 Network RFCs 131
Relacionado con productos y manuales para Servidores De Serie Lantronix XPress-DR-IAP
Servidores De Serie Lantronix MSS4 Guía de usuario
(81 paginas)
(81 paginas)
Servidores De Serie Lantronix EDS4100 Guía de usuario
(163 paginas)
(163 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales