Lantronix XPress-DR-IAP Guía de usuario Pagina 26
- Pagina / 149
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Introduction
Table 4 - Front Panel Components
Item
Component
Name Purpose
1 Screw terminal RXD or RXA
RS-232: RXD (Received Data)
RS-422/485:RXA (Received Data -)
2 Screw terminal CTS or RXB
RS-232: CTS (Clear to Send)
RS-422/485: RXB (Received Data +)
3 Screw terminal RTS or TXB
RS-232: RTS (Request to Send)
RS-422/485: TXB (Transmit Data +)
4 Screw terminal TXD or TXA
RS-232: TXD (Transmit Data)
RS-422/485: TXA (Transmit Data -)
5, 6, 7 Screw terminal NC No connection
8 Screw terminal GND Signal ground
9 Reset switch RESET Push to power reset and initialize
10 LED (Red)
Fault or
Configuration
SOLID: Fault in XPress DR communication
(read error) or
XPress DR is in Configuration
Mode
11 LED (Green) Ready SOLID: Ready, Flashing: Error Message
12 LED (Yellow) Activity FLASHING: Network traffic
13 LED (Green) Link
SOLID:
XPress DR has good Ethernet link
14 Connector (RJ45) Ethernet port RJ45 connector for Ethernet 10BaseT
15 Connector (RJ45) Serial port RJ45 connector for RS-232,RS-422/485
16 LED (Yellow) Serial TXD
FLASHING: Indicates transmission
from the serial port
17 LED (Yellow) Serial RXD
FLASHING: Indicates reception
to the serial port
18 Switch
Switch for
screw block
UP: Serial RS-232
DOWN: Serial RS-422/485
19 Screw terminal DC + (or AC) Operating power, DC positive or AC
20 Screw terminal Ground Earth ground
21 Screw terminal DC – (or AC) Operating power, DC negative or AC
22 Screw terminal Ground Earth ground
Note: For RS-485 2-wire functionality, pins 1 & 4 and 2 & 3 of the screw terminals must be
connected together.
1-12 DSTni-XPress DR User Guide
- DSTni-XPress DR 1
- User Guide 1
- Copyright and Trademark 3
- Disclaimer and Revisions 4
- Declaration of Conformity 5
- Warranty 6
- Sales Offices 7
- Contents 10
- List of Figures 12
- List of Tables 13
- 1.1 DSTni-XPress DR 15
- Introduction 16
- PLC's XPress DR-IAP 17
- 1.4 Serial Interface 19
- 1.5 RJ-45 Serial Connector 20
- 1.7 RJ-45 Ethernet Interface 22
- 1.9 Front Panel Description 25
- 1.10 LEDs 27
- 1.11 Dimensions 28
- 1.13 Power Requirements 29
- 1.14 Reset Switch 29
- 1.15 RS-232/RS-485 Switch 30
- Table 7 - Technical Specs 31
- Getting Started 33
- 2.1.3 Port Number 34
- 2.3.1 DHCP 37
- 2.3.2 AutoIP 37
- 2.4 DeviceInstaller 38
- 2.4.3 Test the IP Address 40
- 2.5 ARP and Telnet 44
- 2.6 Serial Port Login 45
- Configure 47
- 3.2 Using DeviceInstaller 48
- 3.3 Web Manager Page 50
- 3.3.1 Unit Configuration 51
- 3.3.2 Server Properties 52
- 3.3.3 Port Properties 53
- 3.3.4 Update Settings 55
- 3.3.5 Technical Support 55
- 3.4.2 Using the Serial Port 58
- 3.5.1 IP Address 58
- 3.5.5 DHCP Naming 60
- 3.6.1 Baudrate 61
- 3.6.2 I/F (Interface) Mode 61
- 3.6.3 Flow 62
- 3.6.4 Port Number 63
- 3.6.5 Connect Mode 64
- 3.6.6 Remote IP Address 67
- 3.6.7 Remote Port 67
- 3.6.8 DisConnMode 67
- 3.6.10 Pack Control 69
- 3.6.12 Send Characters 70
- 3.6.13 Telnet Terminal Type 70
- 3.7 Expert Settings 71
- 3.8 Security Settings 71
- 3.9 Factory Defaults 73
- 3.11 Get Configuration 73
- 3.12 Set Configuration 74
- 4.1 Protocol Firmware 75
- 4.2.1 Via DeviceInstaller 76
- Firmware 77
- 4.2.2 Via TFTP 79
- 4.2.3 Via Another Unit 79
- 4.2.4 Via the Serial Port 80
- 5.1 Overview 81
- Comm Port Redirector 82
- 5.3 Using Redirector 83
- 5.3.1 Port Setup 84
- 5.3.2 Comm App Setup 84
- 5.3.5 Port Settings 86
- 5.3.6 Listen Mode 86
- 5.3.7 Silent Mode 87
- 5.3.8 TCP Keepalive 87
- 6.1 Technical Support 89
- Troubleshooting 90
- 7.1 Monitor Mode 95
- 0> OK; no error 96
- 8> Wrong parameter(s) 96
- 9> Invalid command 96
- 8.1 UDP Datagrams 97
- 8.2.2 Sending a Setup Record 100
- 8.2.3 The Intel Hex Format 101
- 0300300002337A1E 102
- 8.3 Setup Records 103
- 8.3.1 Channel Parameters 104
- 8.3.2 Interface Mode 105
- 8.3.3 Baud Rate 106
- 8.3.4 Flow Control 106
- 8.3.5 Connect Mode 107
- 8.3.6 Disconnect Mode 108
- 8.3.8 Pack Control 109
- 8.4 IP Addresses 110
- 8.4.3 Host Portion 111
- 8.4.4 Network Address 111
- 8.4.5 Broadcast Address 111
- 8.4.7 Network RFCs 112
- 9.1 Connect Mode Options 114
- Binary to Hex 115
- 9.2 Disconnect Mode Options 117
- 9.4 Interface Mode Options 126
- 9.5 Pack Control Options 127
- 10.1 Class A Network 129
- 10.2 Class B Network 129
- 10.3 Class C Network 129
- 10.4 Network Address 130
- 10.5 Broadcast Address 130
- 10.6 IP Netmask 130
- 10.8 Network RFCs 131
Relacionado con productos y manuales para Servidores De Serie Lantronix XPress-DR-IAP
Servidores De Serie Lantronix MSS4 Guía de usuario
(81 paginas)
(81 paginas)
Servidores De Serie Lantronix EDS4100 Guía de usuario
(163 paginas)
(163 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.176 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales