Lantronix XPort Manual de usuario Pagina 58
- Pagina / 87
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Monitoring the Network
Monitor Mode Commands
The following commands are available in Monitor Mode. Many commands have an IP
address as an optional parameter (xxx.xxx.xxx.xxx). If you enter the IP address, the
command is applied to another unit with that IP address. If you do not enter the IP
address, the command is executed locally.
Note: All commands must be in capital letters.
Table 7-1. Monitor Mode Commands
Command Command Name Function
VS x.x.x.x
Version Queries software header record (16 bytes) of unit
with IP address x.x.x.x.
GC x.x.x.x
Get Configuration Gets configuration of unit with IP address x.x.x.x as
hex records (120 bytes).
SC x.x.x.x
Send Configuration Sets configuration of unit with IP address x.x.x.x
from hex records.
PI x.x.x.x
Ping Pings unit with IP address x.x.x.x to check device
status.
AT
ARP Table Shows the unit’s ARP table entries.
TT
TCP Connection
Table
Shows all incoming and outgoing TCP connections.
NC
Network Connection Shows the unit’s IP configuration.
RS
Reset Resets the unit’s power.
QU
Quit Exits diagnostics mode.
G0, G1, ....,Ge, Gf
Get configuration
from memory page
Gets a memory page of configuration information
from the device.
S0, S1,...,Se, Sf
Set configuration to
memory page
Sets a memory page of configuration information
on the device.
Responses to some of the commands are given in Intel Hex format.
Note: Entering any of the commands listed above generates one of the
following command response codes:
Table 7-4. Command Response Codes
Response Meaning
0> OK; no error
1> No answer from remote device
2> Cannot reach remote device or no answer
8> Wrong parameter(s)
9> Invalid command
7-2 XPort™ User Guide
- XPort™ User Guide 1
- Copyright and Trademark 3
- Contacts 3
- Disclaimer and Revisions 4
- Contents 5
- 5: GPIO Interface 5-1 6
- Purpose and Audience 9
- Chapter Summary 9
- Additional Documentation 10
- Capabilities 11
- Applications 11
- Protocol Support 12
- Addresses and Port Numbers 12
- Logon Methods 13
- Required Information 15
- Assigning an IP Address 16
- Installing DeviceInstaller 16
- Unit Configuration Settings 18
- Getting Started 19
- XPort™ User Guide 3-5 19
- Server Properties 20
- Port Properties 20
- Connect Mode Settings 21
- Dedicated Connection 21
- Flush Mode Input Buffer 21
- Packing Algorithm 22
- Additional Settings 22
- Factory Settings 23
- Update Settings 23
- Accessing Setup Mode 25
- Using the Serial Port 26
- XPort™ User Guide 4-3 27
- IP Address 28
- Set Gateway IP Address 28
- DHCP Name 29
- Baudrate 29
- I/F (Interface) Mode 30
- Port Number 30
- Connect Mode 31
- Incoming Connection 32
- Response 32
- 4-8 XPort™ User Guide 32
- XPort™ User Guide 4-9 33
- Remote IP Address 37
- Remote Port 37
- DisConnMode 38
- Pack Control 39
- Send Characters 40
- Telnet Terminal Type 40
- E-mail Settings 41
- Expert Settings 42
- Security Settings 43
- Disable Port 77FE (Hex) 44
- Disable Web Server 44
- Disable ECHO Ports 44
- Enable Encryption 44
- Factory Defaults 45
- 4-22 XPort™ User Guide 46
- Exit Configuration Mode 47
- Configurable Pins 49
- Control Protocol 50
- Examples 53
- Obtaining Firmware 55
- Reloading Firmware 55
- Figure 6-2. TFTP Window 56
- Monitor Mode Commands 58
- Problems and Error Messages 59
- Troubleshooting 60
- 8-2 XPort™ User Guide 60
- XPort™ User Guide 8-3 61
- Technical Support 62
- Components of the IP Address 63
- Network Address 64
- Broadcast Address 64
- IP Subnet Mask 64
- Network RFCs 65
- AutoIP 66
- ARP and Telnet 67
- Connect Mode Options 69
- Binary to Hex Conversions 70
- Disconnect Mode Options 71
- Enable Disable 72
- Flush Mode Options 73
- Interface Mode Options 78
- Pack Control Options 78
- XPort™ User Guide 82
- Topology 87
- Twisted-Pair Cable 87
- Wide Area Network (WAN) 87
Relacionado con productos y manuales para Hardware Lantronix XPort
Hardware Lantronix TS-DDH Manual de usuario
(20 paginas)
(20 paginas)
Hardware Lantronix UDS2100 Manual de usuario
(83 paginas)
(83 paginas)
Hardware Lantronix UBOX 2100 Manual de usuario
(79 paginas)
(79 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.209 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales