Lantronix XPress DR+ Manual de usuario descargar pdf (Pagina 65)

Chapter 7: Configuration Using Telnet or Serial Port (Setup Mode)

XPress DR+ User Guide 65

At this point, the screen display is the same as when you use a Telnet connection. To

continue, go to step 3 in Telnet Connection above.

Exiting Setup Mode

To exit setup mode:

You have two options:

 To save all changes and reboot the device, select option 9 Save and exit from the

Change Setup menu. All values are stored in nonvolatile memory.

 To exit the configuration mode without saving any changes or rebooting. Select

option 8 Exit without save from the Change Setup menu.

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 ... 115 116

XPress DR+ 1
User Guide 1
Copyright & Trademark 2
Contacts 2
Disclaimer & Revisions 2
Contents 3
Figures 8
Chapter 1: Using This Guide 10
Additional Documentation 11
Chapter 2: Introduction 12
Addresses and Port Numbers 16
Configuration Methods 17
What's in the Box? 18
XPress DR+ Front Panel 19
Serial Interface 20
Serial Connector Pinouts 21
Ethernet Interface 23
Power Requirements 24
Reset Switch 24
Power/Diagnostic LED 25
Dimensions 26
Wall Mount Bracket 27
Product Information Label 27
Chapter 4: XPress DR+W 28
Ad Hoc Network 29
Front Panel Description 31
Hardware Address 32
IP Address 32
WLAN Settings 33
Set Gateway IP Address 34
Change DHCP Device Name: 35
Topology 36
Network Name (SSID) 36
Adhoc Network Channel 36
WPA2/802.11i 39
Fixed or Automatic Data Rate 39
Next Steps 40
Installing DeviceInstaller 41
Assigning an IP Address 41
XPress DR+ User Guide 43 43
Setting Description 43
XPress DR+ User Guide 44 44
Network Configuration 46
Server Configuration 48
Advanced 49
Host List Configuration 50
Channel Configuration 51
Channel 1 52
Port Settings 52
Pack Control 53
Connection Settings - TCP 54
Connect Protocol 55
Endpoint Configuration 55
Connection Settings - UDP 56
Datagram Mode 57
XPress DR+ User Guide 59 59
XPress DR+ User Guide 60 60
Wireless Network Security 61
WEP Options 61
WPA Options 61
Applying Settings 62
Applying Factory Defaults 62
Port (Setup Mode) 63
Serial Port Connection 64
Exiting Setup Mode 65
DHCP Name 68
Baudrate 69
I/F (Interface) Mode 70
Port Number 71
Connect Mode 72
0 0 1 1 1 1 73
0 0 1 1 1 0 73
XPress DR+ User Guide 74 74
Auto Increment Source Port 78
Remote IP Address 78
Remote Port 79
DisConnMode 79
Packing Interval 81
Trailing Characters 81
Send Characters 81
Telnet Terminal Type 82
Channel (Port) Password 82
Transmission Data Rate 86
Enable Power Management 87
Expert Settings (Option 5) 88
Security Settings (Option 6) 89
Disable SNMP 90
SNMP Community Name 90
Disable Telnet Setup 90
Disable Port 77FE (Hex) 90
Default Settings (Option 7) 91
Expert Settings 92
Security Settings 92
Obtaining Firmware 93
Reloading Firmware 93
DeviceInstaller 94
Chapter 12: Monitor Mode 96
XPress DR+ User Guide 98 98
Response Meaning 98
Support 99
XPress DR+ User Guide 100 100
XPress DR+ User Guide 101 101
Technical Support 102
Category Description 103
XPress DR+ User Guide 105 105
AutoIP 106
ARP and Telnet 107
Conversion Table 108
Scientific Calculator 108
Declaration of Conformity 110
Supplementary Information 111
Manufacturer’s Contact 111
Appendix F: Warranty 115
XPress DR+ User Guide 116 116

Comentarios a estos manuales

Sin comentarios

Lantronix XPress DR+ Manual de usuario Pagina 65

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Lantronix XPress DR+