Lantronix Device Server UDS 10 Manual de usuario descargar pdf (Pagina 34)

Getting Started

2-6

UDS-10 User Guide

2.4.2 Assign IP Address and Network Class

Click the Start button on the Task Bar and select Programs \Device Installer \Device

Installer. The Device Installer window displays.

Figure 5 - DeviceInstaller Window

1. Click the IP icon

. The Assign IP Address window displays.

Figure 6 - Assign IP Address Window

2. In the Enter the Hardware or Ethernet Address field, enter the Ethernet address (MAC

address), which is listed on the label on the side of the unit.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 138 139

User Guide 1
Copyright and Trademark 2
Disclaimer and Revisions 3
Declaration of Conformity 4
Warranty 5
Sales Offices 6
Table of Contents 7
UDS-10 User Guide iii 9
Contents 10
UDS-10 User Guide 10
List of Figures 11
List of Tables 12
UDS-10 User Guide vii 13
1. Introduction 15
1.1 UDS-10 16
1.2 UDS-10B 17
1.3 UDS-10-IAP Device Server 18
Introduction 19
UDS-10 User Guide 1-5 19
1.4 Network Protocols 20
1.5 Serial Interface 21
1.6 RJ-45 Ethernet Interface 21
1.7 Ethernet Cable 22
UDS-10 User Guide 1-9 23
1.9 LEDs 24
1.10 Dimensions 25
1.12 Software Support 25
1.13 Power Requirements 26
1.14 Reset Switch 26
Table 3 - Technical Specs 27
2. Getting Started 29
2.1.3 Port Number 30
Ethernet 30
2.3.1 DHCP 32
2.3.2 AutoIP 32
2.4 DeviceInstaller 33
Getting Started 34
2.4.3 Test the IP Address 35
UDS-10 User Guide 2-9 37
2.5 ARP and Telnet 39
2.6 Serial Port Login 40
3. Configuring the Unit 41
3.2 Using DeviceInstaller 42
Configure 43
UDS-10 User Guide 3-3 43
3.3 Web Manager Page 44
3.3.1 Unit Configuration 45
3.3.2 Server Properties 46
3.3.3 Port Properties 47
3.3.4 Technical Support 49
3.3.5 Update Settings 49
UDS-10 User Guide 3-11 51
3.5.5 DHCP Naming 54
UDS-10 User Guide 56
3.6.3 Flow 57
3.6.4 Port Number 57
3.6.5 Connect Mode 58
UDS-10 User Guide 3-19 59
3.6.10 Pack Control 63
3.6.12 Send Characters 64
3.6.13 Telnet Terminal Type 64
3.7 Expert Settings 65
3.8 Security Settings 65
3.9 Factory Defaults 66
3.11 Get Configuration 67
3.12 Set Configuration 68
4.1 Protocol Firmware 69
4.2.1 Via DeviceInstaller 70
Firmware 71
UDS-10 User Guide 4-3 71
4.2.2 Via TFTP 72
4.2.3 Via Another Unit 73
SF x.x.x.x 73
02049 lines loaded 74
4.2.4 Via the Serial Port 74
*** NodeSet 2.0 *** 74
5. DeviceComm Manager 75
UDS-10 User Guide 5-3 77
6. Troubleshooting 79
Troubleshooting 80
UDS-10 User Guide 6-3 81
UDS-10 User Guide 6-5 83
7. Monitor Mode 85
8.1 UDP Datagrams 87
UDS-10 User Guide 8-3 89
8.2.2 Sending a Setup Record 90
8.2.3 The Intel Hex Format 91
00000001FF 91
01002000805F 91
0300300002337A1E 92
8.3 Setup Records 93
8.3.1 Channel Parameters 94
8.3.3 Baud Rate 96
8.3.4 Flow Control 96
8.3.5 Connect Mode 97
UDS-10 User Guide 8-13 99
8.4 IP Addresses 100
8.4.3 Host Portion 101
8.4.4 Network Address 101
192.168.0.0 101
8.4.5 Broadcast Address 101
192.168.0.255 101
8.4.7 Network RFCs 102
9. Binary to Hex Conversion 103
9.1 Connect Mode Options 104
Binary to Hex 105
UDS-10 User Guide 9-3 105
Accept Incoming 106
Connections 106
Response Hex 106
9.2 Disconnect Mode Options 107
UDS-10 User Guide 9-7 109
9.4 Interface Mode Options 115
9.5 Pack Control Options 116
UDS-10 User Guide 9-15 117
10. IP Addresses 119
10.4 Network Address 120
10.5 Broadcast Address 120
10.6 IP Netmask 120
10.8 Network RFCs 121
11. Glossary of Terms 123

Comentarios a estos manuales

Sin comentarios

Lantronix Device Server UDS 10 Manual de usuario Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Lantronix Device Server UDS 10